阳光精品论坛 >> 『 CAE 专栏 』 >> dyna中空材料的设置技巧

本主题已阅读2747次,回复0 篇

作者 | 本页主题： dyna中空材料的设置技巧

even2004      信息：  来自：未填  发贴：1239 贴  积分：244 点 货币：5814 阳光币 注册时间：2008/12/31  资料 好友 消息 引用回复 选择字号91011121415161820253050 dyna中空材料的设置技巧 单物质情况下才能用，多物质情况不能用 Euler/ALE Basics Eulerian fluids such as air or water are generally modeled using *MAT_NULL and an accompanying equation-of-state (*EOS_. . . ) For a case where there is only one Eulerian material, I would recommend you use solid element formulation 12 (single material with void) to model the Eulerian material and any empty cells around the Eulerian material into which that material may ultimately be transported[1]. The empty cells (which typically overlay your Lagrangian parts) are identified using *initial_void. All the Eulerian parts (filled or void) should be given material/EOS properties of the Eulerian material. Use hexahedron (brick) elements and hourglass type 1. A reduced hourglass coefficient, e.g., . 001, is recommended if the Eulerian material is a fluid.   For cases where there are multiple Eulerian materials, use solid formulation 11 (multi-material). For this, each Eulerian material must be assigned to a group using *ale_multi-material_group. Each part within a specific group has identical material properties.   Eulerian meshing can be done using one of the following two approaches: The initial mesh conforms to the material. In other words, there are no mixed (or partially filled) cells in the initial configuration. Mesh lines follow the outer contour of each Eulerian part.  ; A simple orthogonal mesh may be constructed with no restriction that mesh lines follow the outer contour of each Eulerian part. The volume fraction of initially mixed cells must be prescribed via *initial_volume_fraction. Version 970 has a "geometry" option to *initial_volume_fraction that automates the assignment of initial volume fractions to cells.   In either approach, there is no requirement that the Lagrangian nodes align with the Eulerian nodes. In your coupling definition (*constrained_lagrange_in_solid), you may have to increase NQUAD if the structural mesh is coarser than the Eulerian mesh (in order to prevent 'leakage' in the coupling). Your Lagrangian segment normals must point toward the Eulerian fluid (note you can reverse the normals using NORM). If you are coupling Lagrangian solids to the Eulerian fluid, you MUST set CTYPE to 5 unless the slave side is identified by segments instead of by part ID. Set MCOUP to 1 in cases where one of the Eulerian materials dominates the loads imparted to the Lagrangian structure, i.e. its density is much higher than the other Eulerian materials. Typically DIREC should be set to 2 when a penalty-based coupling is used.   As an alternative to coupling (*constrained_lagrange_in_solid), you can, in some cases, merge (share) nodes at the interface between a Lagrangian part and an ALE part. The shared nodes will move as Lagrangian nodes. The interior of the ALE mesh must then be smoothed using one or a combination of smoothing algorithms (see *control_ale) and, if the situation warrants, *ale_smoothing constraints.   To view the Eulerian material in LS-POST, use Fcomp > misc > history var#.   The definition of the history variables are as follows: 1 = density 2 = volume fraction of 1st multi-material group (formulation 11) or single Eulerian material (formulation 12) 3 = volume fraction of 2nd multi-material group (formulation 11) etc.   It's sometimes clearer to view isosurfaces of Eulerian history variables rather than fringes (click on the Frin button and choose Isos). Notes: The command *ale_reference_system(_option) can be utilized in some situations to reduce the spatial extent of the initial Eulerian mesh. This command directs the Eulerian/ALE mesh to move through space in a prescribed manner rather than remaining fixed in space like a pure Eulerian mesh. 编辑 |  发表于 2009/01/05/07:30  |  1 层  进入评分

推荐给朋友 可打印版本 文章模式

论坛跳转： 论坛跳至≡ 论坛管理 ≡ |- 『 论坛版务 』 |- 『 公告栏 』≡ 电脑及网络技术 ≡ |- 『 应用软件 网络技术 』 |- 『 硬件家园 』 |- 『 人才交流 』 ≡ 专业技术讨论区 ≡ |- 『 CAD 专栏 』 |- 『 CAM 专栏 』  |- 『 CAE 专栏 』 |- 『 CFD 专栏 』 |- 『 模具设计 逆向工程 』 |- 『 设计精品欣赏 』≡ 会员区 ≡ |- 『 软件上传与下载 』 |- 『 软件预览 0day介绍 』 |- 『 软件安装及求助 』≡ 休闲一刻 ≡ |- 『 网事闲谈 』 |- 『 文学苑 』 |- 『 美丽贴图 』 |- 『 游戏园地 』≡ 违规处理区 ≡ |- 『 回收站 』

快速回复

文章内容： HTML 代码不可用 关闭BMB Code 关闭Emot Code BMB代码选项： [img] - 开启 [flash] - 开启 [size] - 开启 上传附件[还可传0个]: 开启 最大字节: 200000 字节 最少发帖: 20 篇 标题: 签名 自动URL 动作 动作招呼欢迎灌水无聊负责生气高兴鼓掌等待反对浪漫不要找死去死狂笑傻笑痛哭道别跳舞唱歌害羞比酷救命狂妄拳击我踢我踩饶命眨眼臭美变态拼酒深情恶心惊讶抽烟怀疑拉勾经典同意ＯＫkiss生日晕倒气你错啦加油恭喜简单鼓励过奖原谅大笑考虑感动叹气道谢摇头拥抱无奈   [使用 Ctrl+Enter 直接提交贴子] 你的用户名：  你的密码： 忘了密码? 有效文件类型：---------jpggifziprarpngaceisocgiaspswftxtbmp

阳光精品论坛 >> 『 CAE 专栏 』 >> dyna中空材料的设置技巧

本主题已阅读2747次,回复0 篇

本论坛言论纯属发表者个人意见，与 阳光精品论坛 立场无关 联系我们 Powered by BMForum v5.0 Skin by Bob Shen